Evinrude E-NATION, for those dedicated to water, power, fishing and fun
Reply
Skipper
Posts: 14
Registered: ‎07-20-2011

30 don't run

Hi i have a 30 e tec less than 100 hours on and the EMM dead i had 3 dealrs looke at and said no 

BRP will not work with us and no dealrs want it. junk 

Admiral
Posts: 6,298
Registered: ‎07-14-2011

Re: 30 don't run

 

 

Hi,

I'm sure that there is a lot more to the story than just the information that you have given us.  Please send an email with the engine serial number, dealers' names, and a history of your motor to  brp.care@brp.com .  They will investigate your situation and report back to you.

 

We are sorry to hear that your experiences with your Evinrude have not been satisfactory to you and perhaps we can rectify that.

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.


Skipper
Posts: 14
Registered: ‎07-20-2011

Re: 30 don't run

[ Edited ]

The Dealers don't want to work on it beacuse they don't have the techs to work on it.

they went with Yamaha and the Mercury beacuse of this problem and the dealers told us this.

they only sell  a evinrude and don't want to work on it if there is a problem and  evinrude don't want to sell

a EMM with out a dealer. i only have Yamaha or Merucry dealers that are 45 minutes  drive  to me 

Admiral
Posts: 6,298
Registered: ‎07-14-2011

Re: 30 don't run

Send the email to brp.care@brp.com

 

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.


Skipper
Posts: 14
Registered: ‎07-20-2011

Re: 30 don't run

we already did that only thing they told us is that take it to a dealer what dearler we don't 

have a Evinrude dealer they went to Yamaha or Merucry they use to be a Evinrude dealer but they had a hard time with BRP

that is why they left and went to Yamaha or Merucry. 

 

Highlighted
Admiral
Posts: 6,298
Registered: ‎07-14-2011

Re: 30 don't run

Usually they will suggest dealers in your area.

 

 

Click on this link to see if you can find one. Where are you located?

 

 

http://www.evinrude.com/en-US/find-a-dealer.html

 

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.