Evinrude E-NATION, for those dedicated to water, power, fishing and fun
Reply
Highlighted
Captain
Posts: 162
Registered: ‎07-28-2015

CORRECT TRIM/TILT FLUID FOR E75DPLABA

[ Edited ]

I'm sure my Trim/Tilt is in need of some fluid. I have purchased a tube P/N 775612 for $9.00 and a quart bottle P?N 763439 for $29.59.

One says Bio degradeable and the other nothing. This is my first time doing this so I'm sure the fluid that it came with was done at the factory.

So which one do I use???

Also, would the trim pump/motor be covered under my extended 2 year warranty which is inforce till 2020?

Thanks 

Highlighted
Admiral
Posts: 8,573
Registered: ‎07-14-2011

Re: CORRECT TRIM/TILT FLUID FOR E75DPLABA

 

 

 

It is listed in your operator's guide that your motor uses the Biodegradable trim fluid. It cannot be mixed with ATF or other petroleum based fluids.

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.


Highlighted
Captain
Posts: 162
Registered: ‎07-28-2015

Re: CORRECT TRIM/TILT FLUID FOR E75DPLABA

Ok Bio I have what about warranty if its having issues?
Highlighted
Admiral
Posts: 8,573
Registered: ‎07-14-2011

Re: CORRECT TRIM/TILT FLUID FOR E75DPLABA

[ Edited ]

 

 

If your motor is within the warranty coverage period, no problem, your dealer will take care of it.

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.


Highlighted
Captain
Posts: 162
Registered: ‎07-28-2015

Re: CORRECT TRIM/TILT FLUID FOR E75DPLABA

So I'll be dropping off at Jarvis Marine in Tuckerton for warranty repair of my trim/tilt pump. It's really leaking bad when raising up and down from the top of the pump.

My warranty card says I'm good till July 17,2020

Thank God!!!

 

  

Highlighted
Captain
Posts: 162
Registered: ‎07-28-2015

Re: CORRECT TRIM/TILT FLUID FOR E75DPLABA

Thanks Evinrude and Jarvis Marine for the quick turn around on the trim/tilt assembly replacement, "Under Warranty "!
I really appreciate it. Now I can get on with the rest of Summer preparation.