Evinrude E-NATION, for those dedicated to water, power, fishing and fun
Reply
Highlighted
Skipper
bigedd
Posts: 6
Registered: ‎07-28-2018
Accepted Solution

G2 Suddenly Shudders and Cuts out no fault codes

‎10-11-2018 03:40

Hi there my 300HP G2 102hrs runs as smooth as silk. Was out today doing 4000Rpm for about 25 minutes then cranked it to 5000Rpm and within 30 seconds it starts Choking, vibrating and cuts out. No fault Codes. Tried to resart bit sound very very rough and cuts out again. Ant clues as to what may be wrong??

Report Inappropriate Content
Message 1 of 7 (1,711 Views)
Reply
0 Kudos
Highlighted
Captain
Nordmann
Posts: 357
Registered: ‎08-11-2011

Re: G2 Suddenly Shudders and Cuts out no fault codes

‎10-11-2018 04:21

Sounds like it's running out of fuel at high demand. Check fuel system pressure and vacuum. Is it a new boat or re-power? If latter you may need to replace old fuel-system.

Report Inappropriate Content
Message 2 of 7 (1,710 Views)
Reply
0 Kudos
Highlighted
Skipper
bigedd
Posts: 6
Registered: ‎07-28-2018

Re: G2 Suddenly Shudders and Cuts out no fault codes

‎10-11-2018 05:40

new engine. Thanks for that I was hoping a minor fuel issue

 

 

Report Inappropriate Content
Message 3 of 7 (1,705 Views)
Reply
0 Kudos
Highlighted
Skipper
bigedd
Posts: 6
Registered: ‎07-28-2018

Re: G2 Suddenly Shudders and Cuts out no fault codes

‎10-11-2018 05:40

nut it also cuts out on idle now

Report Inappropriate Content
Message 4 of 7 (1,704 Views)
Reply
0 Kudos
Highlighted
Admiral
BluewaterBill
Posts: 9,464
Registered: ‎07-14-2011

Re: G2 Suddenly Shudders and Cuts out no fault codes

‎10-11-2018 08:02

 

 

As you probably realized, it is time your motor should be checked out right away by an Evinrude dealer. It could be something as simple as contaminated fuel or a fuel delivery problem or something more technical.

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.


Report Inappropriate Content
Message 5 of 7 (1,684 Views)
Reply
0 Kudos
Highlighted
Skipper
bigedd
Posts: 6
Registered: ‎07-28-2018

Re: G2 Suddenly Shudders and Cuts out no fault codes

‎10-11-2018 08:04

yep got it booked in for tomorrow thanks again. Just wanted a heads up on what the problem is before i get conned into rebuilding the engine or something silly like that

 

Report Inappropriate Content
Message 6 of 7 (1,682 Views)
Reply
0 Kudos
Highlighted
Captain
DaleH
Posts: 28
Registered: ‎09-04-2018

Re: G2 Suddenly Shudders and Cuts out no fault codes

‎10-11-2018 12:27

Sounds like water in the fuel to me ... but not privy to what sensors that puppy might have ... 

Report Inappropriate Content
Message 7 of 7 (1,660 Views)
Reply
0 Kudos