09-11-2016 03:06
Hello,
A friend just puchased a set of 2016 E300 G2's and his grease gun does not fit the nipples on the portiside of the engines. What type of fitting is required for these?
Thanks.
PS. If I am posting this in the wrong place please also let me know as I am new at this.
09-12-2016 04:22 - edited 09-12-2016 04:26
The grease fittings are the same type on both sides of the engine.
Is your friend thinking that the hydraulic fittings for bleeding the steering unit are grease fittings? They are larger in diameter than regular grease fittings and should not be touched.
"There is never just one thing wrong with a boat";
-- Travis McGee, main character in a book series by John D. McDonald
***************
The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.
The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.
09-20-2016 08:36
09-21-2016 07:15
I don't think the manual shows the grease nipples of G2.
How many grease nipples are there and where are they located ?.
Ilkka.
09-21-2016 07:39
Grease fittings are underneath the pivot caps. You are correct, they are not shown in the operator's guide
"There is never just one thing wrong with a boat";
-- Travis McGee, main character in a book series by John D. McDonald
***************
The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.
The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.
09-02-2019 06:42
09-03-2019 08:57
Remove the large diameter silver or chrome caps and the fittings are visible. Use a quality marine grease such as Evinrude Triple-Guard at least once a year in saltwater environments.
"There is never just one thing wrong with a boat";
-- Travis McGee, main character in a book series by John D. McDonald
***************
The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.
The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.
11-04-2019 10:36 - edited 11-04-2019 10:37
Do those caps twist off?
11-05-2019 08:53
I see the two screws in the silver cap with what looks like an Allen head. I can't figure out the size of the head. Tried my metric and regulate Allen wrenches and nothing works. Any clues?
11-05-2019 09:36
Torx screws, not Allen.