Evinrude E-NATION, for those dedicated to water, power, fishing and fun
Reply
Captain
Posts: 60
Registered: ‎03-21-2014
Accepted Solution

Measures for the new 150 G2

Hi Bill, for the old 150 E-Tec there was/is (can't seem to find it again) a drawing/schematic available showing the measures of the motor, how far forward it would go tilted up, measured from the transom etc. Is there such a drawing available for the new G2? 

Admiral
Posts: 8,175
Registered: ‎07-14-2011

Re: Measures for the new 150 G2

[ Edited ]

Go to shop2.evinrude.com, go to PARTS, the correct engine model number, then select profile drawings

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.


Captain
Posts: 60
Registered: ‎03-21-2014

Re: Measures for the new 150 G2

Thank You, BillSmiley Happy

Captain
Posts: 60
Registered: ‎03-21-2014

Re: Measures for the new 150 G2

I find measures for the 3.4 liter motors but not for the new 2.7 liters. Are they the same?

Admiral
Posts: 8,175
Registered: ‎07-14-2011

Re: Measures for the new 150 G2

You have to look them up by model number such as  C150PLAAC - (G2 66° V6, 2.7 L)

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.


Captain
Posts: 42
Registered: ‎04-03-2018

Re: Measures for the new 150 G2

Hello,

Whats the torque number of the G2 150 H.O in NM?

Highlighted
Admiral
Posts: 8,175
Registered: ‎07-14-2011

Re: Measures for the new 150 G2

g2 e-tec 150 TORQUE COMPARISONS.jpg

 

1 ft-lb = 1.36 N-m

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.


Captain
Posts: 42
Registered: ‎04-03-2018

Re: Measures for the new 150 G2

Whats the TORQUE diffence between 200 G2 and 200 H.O G2? 

Admiral
Posts: 8,175
Registered: ‎07-14-2011

Re: Measures for the new 150 G2

There is no published torque chart for the 200 HO engine but you can figure that it is close in shape to the 250 HO model but with lesser torque numbers.  Here also is a  crankshaft torque curve of the 150 HO Evinrude E-TEC G2 engine. The 200 will be similar but with higher torque numbers. 

 

NOTE: Crankshaft torque

 

G2 150 Torque chart comparison.jpg

 

 

 

 

 

NOTE:  Propshaft toque

 

G2 Torque Chart 250 HO.png

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.


Captain
Posts: 42
Registered: ‎04-03-2018

Re: Measures for the new 150 G2

Whats the idle rpm at N for the big blocks 3.4 ltrs? Also at F