Evinrude E-NATION, for those dedicated to water, power, fishing and fun
Reply
Highlighted
Captain
Posts: 20
Registered: ‎08-04-2011

Props on Etech 200 G2

I have three props, one is renegade four blade.  they would fit on my older etechs but with the new G2 models, which  i am repowering with,  these props will not fit on this engine as I am told.  do they make a kit to put in these older props to be used on the newer  models engines? 

Admiral
Posts: 8,179
Registered: ‎07-14-2011

Re: Props on Etech 200 G2

 

 

If your propellers have the TBX replaceable hub system in them, you can purchase the G2 insert kits and use those props on your new motor.

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.


Captain
Posts: 20
Registered: ‎08-04-2011

Re: Props on Etech 200 G2

unfortunately they do not have the hub kits.  It is the old style hubs.  was hoping that maybe an after market hub was made so could use them as spare props.

Admiral
Posts: 8,179
Registered: ‎07-14-2011

Re: Props on Etech 200 G2

You may be able to get a dealer to give you some trade-in on them if in very good shape, or post them in free classifieds in your area or in local thrift papers that you see in the grocery stores. 

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.


Mate
Posts: 4
Registered: ‎04-30-2018

Re: Props on Etech 200 G2

I have tried 3 different raker props with inserts from dealer and prop shop. The prop will not go all the way down and seat on the shaft? Help!!!

Mate
Posts: 4
Registered: ‎04-30-2018

Re: Props on Etech 200 G2

I have a 2016 250 hp G2. I have tried 3 different Raker HO props with inserts from the dealer and a prop shop. I cannot get the prop to seat. It stops about 3" from being seated. Help?

Admiral
Posts: 8,179
Registered: ‎07-14-2011

Re: Props on Etech 200 G2

what part number TBX hub is installed?

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.


Mate
Posts: 4
Registered: ‎04-30-2018

Re: Props on Etech 200 G2

Got from Prop Shop- Michigan Wheel MODEL XHS-II HUB KIT 228

Admiral
Posts: 8,179
Registered: ‎07-14-2011

Re: Props on Etech 200 G2

 

Sorry, we cannot comment or help on competitive and non-Evinrude products. Contact your seller for assistance.

 


@1fishing wrote:

Got from Prop Shop- Michigan Wheel MODEL XHS-II HUB KIT 228


 

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.


Mate
Posts: 4
Registered: ‎04-30-2018

Re: Props on Etech 200 G2

ok thanks, can I get the Hub kit from Evinrude??