Evinrude E-NATION, for those dedicated to water, power, fishing and fun
Reply
Mate
Posts: 2
Registered: ‎05-12-2016

Propeller

I have an ETEC 250hp on a 24' tritoon. Prop was damaged last year and I find no markings other than Rebel to detrermine what I have. Looking for suggestions on what prop I should use. I pull tubes and want to go over 50mph(not while pulling tubes).

 

Thanks in advance.

 

Jim

Admiral
Posts: 7,115
Registered: ‎07-14-2011

Re: Propeller

 

 

HI Jim,

 

 

You can find the Rebel propeller size stamped on the aft end of the hub where the splined washer and propnut are fastened.

 

For your own research, click on the PERFORMANCE  REPORTS  on bottom of  the Evinrude website and peruse them for rigs similar to yours. Here is a hotlink to about 196 pontoon boat reports. You can narrow those down by selecting the various 250 HP models. You can also check with your dealer, the pre-delivery form that you signed with the dealer, often the prop size is on the bill of sale, or contact the pontoon boat manufacturer.

 

http://www.evinrude.com/en-us/tools/performance-reports-library?engineId=&boatBrandId=&boatTypeId=Po...

 

 

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.


Captain
Posts: 36
Registered: ‎04-03-2018

Re: Propeller

What prop do you recommend for waves to be good and just run over and jump smoothly over them with smooth landings.

The prop size thats on my evinrude e-tec G2 150 H.O is a 14.5 x 22" Raker ( all vents closed ) 6000 rpm att WOT running 52 knots. Weight with crew aqnd fuel is approximately 900 kilos. What prop should i get? I have my thoughts on a rx4 15 x 20", please give me some suggestions. 

Admiral
Posts: 7,115
Registered: ‎07-14-2011

Re: Propeller

[ Edited ]

22" RX4 to get the revs close to 5600-5800 rpm. It is trial and error. 

 

You do not have to post the same question multiple times here on this site 

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.


Captain
Posts: 36
Registered: ‎04-03-2018

Re: Propeller

do you think the Rx4 Will be smoother in waves and rough water? How much is evinrude´s foot throttle btw?

Admiral
Posts: 7,115
Registered: ‎07-14-2011

Re: Propeller

[ Edited ]

The four blades on the RX4 makes for smoother running and it is why it is best for rough water and most boats.

 

Contact your dealer for pricing and installation.

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.


Captain
Posts: 36
Registered: ‎04-03-2018

Re: Propeller

Does the warranty cover if you have a noscone glued on the gearbox? I´m talking about Nitra racing´s nosecones for evinrude g2. 

Admiral
Posts: 7,115
Registered: ‎07-14-2011

Re: Propeller

If the nosecone somehow caused a problem to exist, then the answer is no. However if you ever needed a gearcase replacement, they would not reimburse you for the nosecone or labor to install a new one. If the gearcase had to be returned, you would have to remove it.

 

 

 


"There is never just one thing wrong with a boat";
                    -- Travis McGee, main character in a book series by John D. McDonald 


 



***************

The factory recommends that a properly trained technician service your Johnson or Evinrude outboard motor. Should you elect to perform repairs yourself, use caution, common sense, and observe safety procedures in the vicinity of flammable liquids, around moving parts, near high-temperature components, and working with electrical or ignition systems.

The information offered here is only general in nature and should not be construed as complete factory approved procedures, techniques, or specifications. Always use the proper service manual for your motor, up-to-date service literature, the correct tools, and have an understanding of how to proceed with troubleshooting and repair methods. If you are unsure or uncomfortable with a procedure, a situation, or a technique, enlist the services of a factory trained technician.


Captain
Posts: 36
Registered: ‎04-03-2018

Re: Propeller

I mean like if the powerhead or an oil fault would occur, would the glued nosecone make the warranty go of?

Captain
Posts: 36
Registered: ‎04-03-2018

Re: Propeller

Does evinrude have a 5 blade propeller? I tried the rx4 but it wasn´t smooth enough and looses much grip when im running on high trim. What other options do i have?